KS M 6080 Class 1(Air drying type Traffic Paint)
1. Product Overview
- This paint is produced by using an acrylic synthetic resin as a binder, mixed with white, yellow pigment and extender. This paint is one-component paint used to draw traffic signs such as roads and airstrips.
2. Product Characteristics
- Fast drying and excellent workability.
- Excellent hiding power and adhesion.
- Excellent abrasion resistance.
- Excellent in water resistance, alkali resistance, weather resistance.
3. Properties
Color | White, Yellow | Recommended film thickness (㎛) | Wet film : 200 ㎛ |
Viscosity (at 25℃) | 85 - 95KU | Dry film : 100 ㎛ |
Specific gravity | White : 1.50 – 1.50 | Drying time (20℃) | set-to-touch : min. 5 |
| Yellow : 1.45 - 1.50 | | no-pick-up : min. 20 |
Solids by volume (%) | 52 ±2% | Coverage (㎡/ℓ) | 4.9 ㎡/ℓ |
Gloss | Matt | | 32 m/ℓ (thickness 15cm) |
Application | brush, roller, spray | | |
※ The application area may vary depending on the condition of the road surface and the coating method.
4. Reflective glass beads
Type | Consumption (kg/m2) | Application |
KS L 2521 type 2 (106 ~ 600㎛) | 0.29 kg/m2 | manual and spray |
5. Painting specification
- Surface preparing : Remove the moisture, dirt, oil etc from the surface of the road.
- Surface condition : To avoid condensation of moisture, the surface temperature should be 3 ℃ above the dew point and the relative humidity below 85%.
- Application : brush, roller, spray
- Thinner : non thinning
- Temperature : Use at atmospheric temperature 5 ℃ ~ 40 ℃.
( ※ Operation below 5 ℃ will causes poor drying and poor adhesion. )
- Vehicle pass available time : min. 20 / 20 ~ 25℃ (Recommended film thickness dry. 100㎛)
6. Cautions on painting
- Avoid painting when the relative humidity is above 85% and the substrate surface temperature is below 5℃.
( Occur of problem (crack, poor adhesion etc.) )
- Use after confirming the compatibility with the old film on repairing the old film.
- Do not mix with other company products.
- Isolate from fire because the rate of evaporation is fast.
- Remove the moisture, dirt, oil etc from the surface of the road.
- Stir to be mixed uniformly before application.
- If diluent is used, dilute to within 10% by using specified diluent.
- It is necessary to coat with the specified coating amount. In case of excessive coating at one time, the problem of drying failure may occur.
- If the coating surface is new concrete, apply it when the curing time is sufficient (curing for more than 30 days at 20 ℃), the pH is 7 ~ 9 and the water content is less than 8%.
- In case of repetitive painting, it should be painted after confirming that it is sufficiently dried.
(Lifting, wrinkling, reverling, etc. may ocuur)
- Use at atmospheric temperature 5 ℃ ~ 40 ℃. To avoid condensation of moisture, the surface temperature should be 3 ℃ above the dew point and the relative humidity below 85%.
7. Cautions on handling
- Prohibition of use other than the recommended use.
- Keep out of reach of children. Do not apply to children's equipment and food storage containers.
- When transporting, storing and handling the product, avoid fire and direct sunlight, store it in a dry and dark, keep the container sealed, and keep the filling port facing up.
- To prevent environmental pollution, completely use the contents and dispose of the remaining amount through the designated waste disposal company.
- Contains organic solvents and may cause headaches, dizziness, and other health problems. Avoid ingestion, inhalation of vapors, and skin contact.
- Do not store or paint near fire. Avoid sparks due to impact, friction, etc. during handling.
- In case of contact with eyes, rinse immediately with plenty of water and seek doctor.
- If inhaled, move to a place with clear air. If irritation develops, consult a doctor immediately.
- If ingested, seek medical advice immediately.
- Use the product in efficacy period. (12 months)
※ For more information on product safety, see the Material Safety Data Sheet (GHS-MSDS).